Stap 9: PD lijn volgeling
Iets geavanceerder programma. Nog een work in progress, maar dit werkt. KP = 1, Kd = 2
/* ABLB * ActoBitty Line Bot * * base robot Actobotics ActoBitty: * https://www.servocity.com/html/actobitty_2_wheel_robot_kit.html#.VthCuvkrI-U * * microcontroller board DFRobot Romeo 2 (has built in motor controller): * http://www.dfrobot.com/wiki/index.php/Romeo_V2-All_in_one_Controller_(R3)_(SKU:DFR0225) * * mount panel for board: * http://www.thingiverse.com/thing:1377159 * * line follower array from Sparkfun: * https://github.com/sparkfun/Line_Follower_Array * https://learn.sparkfun.com/tutorials/sparkfun-line-follower-array-hookup-guide * position provided ranges from -127 (far L) to 127 (far R) * * PID quick tutorial * http://letsmakerobots.com/node/39972 * */ #include "Wire.h" // for I2C #include "sensorbar.h" // needs SparkFun library // Uncomment one of the four lines to match your SX1509's address // pin selects. SX1509 breakout defaults to [0:0] (0x3E). const uint8_t SX1509_ADDRESS = 0x3E; // SX1509 I2C address (00) //const byte SX1509_ADDRESS = 0x3F; // SX1509 I2C address (01) //const byte SX1509_ADDRESS = 0x70; // SX1509 I2C address (10) //const byte SX1509_ADDRESS = 0x71; // SX1509 I2C address (11) SensorBar mySensorBar(SX1509_ADDRESS); // will try to avoid floating point math const byte Kp = 1; const byte Kd = 2; const byte MAXSPEED = 128; // slow things down for testing purposes int Lspeed = MAXSPEED; // int since may exceed 255 in calculations, but will ultimately be constrained int Rspeed = MAXSPEED; const int ButtonPin = 0; int buttonVal = 0; boolean goFlag = false; int error = 0; int lastError = 0; // Romeo standard pins int Lmotor = 5; // M1 Speed Control int Rmotor = 6; // M2 Speed Control int Ldir = 4; // M1 Direction Control int Rdir = 7; // M1 Direction Control void setup() { //Default: the IR will only be turned on during reads. mySensorBar.setBarStrobe(); //Other option: Command to run all the time //mySensorBar.clearBarStrobe(); //Default: dark on light mySensorBar.clearInvertBits(); //Other option: light line on dark //mySensorBar.setInvertBits(); //Don't forget to call .begin() to get the bar ready. This configures HW. uint8_t returnStatus = mySensorBar.begin(); /* if(returnStatus) { Serial.println("sx1509 IC communication OK"); } else { Serial.println("sx1509 IC communication FAILED!"); } Serial.println(); */ } // end setup() void loop() { buttonVal = analogRead(ButtonPin); if (buttonVal < 30){ // button 1 halt(); goFlag = false; } else if (buttonVal < 175){ // button 2 //Command to run all the time - allow calibration mySensorBar.clearBarStrobe(); int i = mySensorBar.getPosition(); } else if (buttonVal < 360){ // button 3 //Default: the IR will only be turned on during reads. mySensorBar.setBarStrobe(); } // else if (buttonVal < 540){ // button 4 // // for future use // } else if (buttonVal < 800){ // button 5 - run line follower program goFlag = true; delay(3000); // 3 sec delay to back off // include visual indicator later } if (goFlag) { error = mySensorBar.getPosition(); // position gives distance from midline, i.e. the error // want to be as fast as possible, so will just slow down necessary wheel for correction // rather than trying to speed up one and slow the other if (error < 0){ // robot has drifted right; slow down L wheel Rspeed = MAXSPEED; Lspeed = MAXSPEED + (Kp * error) + (Kd * (error - lastError)); // plus since error is negative, will result in negative values for proportionate term Lspeed = constrain(Lspeed, 0, MAXSPEED); } else if (error > 0){ // robot has drifted L; slow down R wheel Rspeed = MAXSPEED - (Kp * error) - (Kd * (error - lastError)); Rspeed = constrain(Rspeed, 0, MAXSPEED); Lspeed = MAXSPEED; } else{ // position is zero; full on both Rspeed = MAXSPEED; Lspeed = MAXSPEED; } fwd(Lspeed,Rspeed); } // end if (goFlag) } // end loop() void halt(void) // Stop { digitalWrite(Lmotor,LOW); digitalWrite(Rmotor,LOW); } void fwd(byte l,byte r) // Move forward { analogWrite (Lmotor,l); // PWM Speed Control digitalWrite(Ldir,LOW); // LOW for fwd analogWrite (Rmotor,r); digitalWrite(Rdir,LOW); } // don't need these functions for basic line follower //void rev(byte l,byte r) // Reverse //{ // analogWrite (Lmotor,l); // digitalWrite(Ldir,HIGH); // analogWrite (Rmotor,r); // digitalWrite(Rdir,HIGH); //} //void spinR(byte l, byte r) //{ // analogWrite (Lmotor,l); // digitalWrite(Ldir,LOW); // L fwd, R rev to spin R (clockwise) // analogWrite (Rmotor,r); // digitalWrite(Rdir,HIGH); //} //void spinL(byte l, byte r) //{ // analogWrite (Lmotor,l); // digitalWrite(Ldir,HIGH); // R fwd, L rev to spin L (counterclockwise) // analogWrite (Rmotor,r); // digitalWrite(Rdir,LOW); //}