Stap 8: Basic-programma
Dit programma werd vanaf de SparkFun meest Basic Line volgeling gewijzigd. Het werkt, maar niet scherpe draait goed. Ik ben nog steeds bezig de juiste PID lijn sensing.
/* ABLB * ActoBitty Line Bot * * base robot Actobotics ActoBitty: * https://www.servocity.com/html/actobitty_2_wheel_robot_kit.html#.VthCuvkrI-U * * microcontroller board DFRobot Romeo 2 (has built in motor controller): * http://www.dfrobot.com/wiki/index.php/Romeo_V2-All_in_one_Controller_(R3)_(SKU:DFR0225) * * mount panel for board: * http://www.thingiverse.com/thing:1377159 * * line follower array from Sparkfun: * https://github.com/sparkfun/Line_Follower_Array * */ #include "Wire.h" // for I2C #include "sensorbar.h" // needs SparkFun library // Uncomment one of the four lines to match your SX1509's address // pin selects. SX1509 breakout defaults to [0:0] (0x3E). const uint8_t SX1509_ADDRESS = 0x3E; // SX1509 I2C address (00) //const byte SX1509_ADDRESS = 0x3F; // SX1509 I2C address (01) //const byte SX1509_ADDRESS = 0x70; // SX1509 I2C address (10) //const byte SX1509_ADDRESS = 0x71; // SX1509 I2C address (11) SensorBar mySensorBar(SX1509_ADDRESS); // based on SparkFun MostBasicFollower code // Define the states that the decision making machines uses: #define IDLE_STATE 0 #define READ_LINE 1 #define GO_FORWARD 2 #define GO_LEFT 3 #define GO_RIGHT 4 uint8_t state = 0; // Romeo standard pins int Lmotor = 5; // M1 Speed Control int Rmotor = 6; // M2 Speed Control int Ldir = 4; // M1 Direction Control int Rdir = 7; // M1 Direction Control void setup() { //Default: the IR will only be turned on during reads. mySensorBar.setBarStrobe(); //Other option: Command to run all the time //mySensorBar.clearBarStrobe(); //Default: dark on light mySensorBar.clearInvertBits(); //Other option: light line on dark //mySensorBar.setInvertBits(); //Don't forget to call .begin() to get the bar ready. This configures HW. uint8_t returnStatus = mySensorBar.begin(); /* if(returnStatus) { Serial.println("sx1509 IC communication OK"); } else { Serial.println("sx1509 IC communication FAILED!"); } Serial.println(); */ } // end setup() void loop() { uint8_t nextState = state; switch (state) { case IDLE_STATE: halt(); // Stops both motors nextState = READ_LINE; break; case READ_LINE: if( mySensorBar.getDensity() == 0) { nextState = IDLE_STATE; break; } else if( mySensorBar.getDensity() < 7 ) { nextState = GO_FORWARD; if( mySensorBar.getPosition() < -50 ) { nextState = GO_LEFT; } if( mySensorBar.getPosition() > 50 ) { nextState = GO_RIGHT; } } else { nextState = IDLE_STATE; } break; case GO_FORWARD: fwd(128,128); nextState = READ_LINE; break; case GO_LEFT: fwd(16,160); // L a little slower R a bit faster nextState = READ_LINE; break; case GO_RIGHT: fwd(160, 16); nextState = READ_LINE; break; default: halt(); // Stops both motors break; } state = nextState; //delay(100); } // end loop() void halt(void) // Stop { digitalWrite(Lmotor,LOW); digitalWrite(Rmotor,LOW); } void fwd(byte a,byte b) // Move forward { analogWrite (Lmotor,a); // PWM Speed Control digitalWrite(Ldir,LOW); // LOW for fwd analogWrite (Rmotor,b); digitalWrite(Rdir,LOW); }